#Cisco packet tracer icon how to#

Click the packet icon on the right menu as seen below:Д¬lick on PC0 and then click PC1. You can confirm that your network works by sending out a packet of information from PC0 to PC1, and vice versa. Then click the FastEthernet tab on the left column to set the actual computerвЂ™s IP address to be on the network. Enter the corresponding IP address of the routerвЂ™s interface, which is 192.168.10.1. Under global settings you will find a field for the gateway. It will allow the computer to interface with another network, so our ping wonвЂ™t work without it!Д¬lick on PC0 to bring up the configuration menu. The gateway is the address we assigned to the Ethernet port that the desktop is connected to. Our last step is to configure the gateway on each desktop computer. If you test out a ping, you will notice that the computers still donвЂ™t communicate, however! Configuring The Gateway In Packet Tracer Type ip address 192.168.20.1 255.255.255.0ДЄt this point our router is configured properly. Press Ctrl + Z to go back to the previous mode.Дў. If you donвЂ™t, there still wonвЂ™t be a connection to PC1! Make sure to enter the IP address carefully as seen below:ДЎ. Now we have to do the same thing for fastethernet0/1. %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up ThatвЂ™s it! You should now see a message similar to the following: Type no shutdown to open the interface up for business. Type ip address 192.168.10.1 255.255.255.0 to assign an IP address and subnet mask to the interface.Д¦. Type interface fastethernet0/0 to access Ethernet0/0ДҐ. Type config terminal (or config t for short) to access the configuration menu.Д¤. Type enable to get to privileged mode (this gives you more options in configuring the router)ДЈ. If youвЂ™ve used the Cisco IOS before, you will notice it looks and acts the same way.Дў. Now click on the CLI tab to access the configuration menu. Although they are physically connected, they are in a state that is known as being in administrative shut down. Next we have to open the Ethernet ports to allow communication. Your network should be similar to the one below at this point:ДЄ router that is turned off doesnвЂ™t work very well! Click on your router to bring up the configuration menu and verify that it is turned on.When on, there will be a small green light below the switch as seen in the diagram. Once the router is configured correctly, the red dots will turn green to indicate the devices are able to communicate.Дo the same operation to PC1, only this time connect the cable to FastEthernet0/1 since FastEthernet0/0 is already taken by PC0. You can tell by the red dots that are present on both ends of the connection.

You will notice that although a link is established, it is not functional. Now click the PC0 and select FastEthernet. Click on Router0, and connect the cable via FastEthernet0/0 as seen below: When you connect like-devices(Such as a router and computer) you use a crossover cable, so you should select copper cross-over cable from the second menu to the immediate right. Now select connections from the same bottom left-hand corner.

Do this twice to make two computers appear below the router. We will be setting up a very basic network that allows two computers to communicate, so the next step is to select end devices from the bottom left-hand corner and drag it to the sandbox screen. Open the program and select the router from the lower left-hand corner, and drag it into the center of the sandbox screen as seen below.

#Cisco packet tracer icon how to#

However, learning how to configure a router with Packet Tracer will put professionals on the right track to mastering the program in about half an hour.Д«y this time, you should already have the Packet Tracer download and have it installed on your computer. Being a development program, this is only natural. Computer networking professionals getting started with Packet Tracer may find the interface to be flustered.